crudlet.org

Home > To Connect > Symantec Unable To Connect To Database

Symantec Unable To Connect To Database

Contents

Error Error 11501:Unable to connect to the database.Make sure that you have entered the correct database parameters and that a firewall is not blocking the connection. Try these resources. Close Login Didn't find the article you were looking for? Create a SymAccount now!' Error 11501:Unable to connect to the database. Source

If it staysstartedthen go ahead and log into theSymantec Endpoint Protection Managerand everything should now be working properly. For 32 Bit, type: dbsrv12 -f"C:\Program Files\Symantec\Symantec Endpoint Protection Manager\db\sem5.db" For 64 Bit, type: dbsrv12 -f"C:\Program Files (x86)\Symantec\Symantec Endpoint Protection Manager\db\sem5.db" and pressEnter. logo-symantec-dark-source Loading Your Community Experience Symantec Connect You will need to enable Javascript in your browser to access this site. © 2016 logo-symantec-dark-source Loading Your Community Experience Symantec Connect You will Supported Products A-Z Get support for your product, with downloads, knowledge base articles, documentation, and more. https://www.symantec.com/connect/forums/suddenly-cannot-open-sepm-console-due-unable-connect-database

Symantec Endpoint Protection Manager + Failed To Connect To The Server

Supported Products A-Z Get support for your product, with downloads, knowledge base articles, documentation, and more. Thank you for your feedback! Submit a False Positive Report a suspected erroneous detection (false positive).

Information for: Enterprise Small Business Consumer (Norton) Partners Our Offerings: Products Products A-Z Services Solutions Connect with us: Support Close Login Didn't find the article you were looking for?

Did this article resolve your issue? Unable to start the embedded database service. Education Services Maximize your product competency and validate technical knowledge to gain the most benefit from your IT investments. In performing the Disaster Recovery procedure to restore the SEPM Webserver service, select a port number other than the default port 8443.

Submit a False Positive Report a suspected erroneous detection (false positive).

Information for: Enterprise Small Business Consumer (Norton) Partners Our Offerings: Products Products A-Z Services Solutions Connect with us: Support Cause Incorrect authentication type selected while configuring the database settings. Translated Content This is machine translated content Login to Subscribe Please login to set up your subscription. his explanation Thank you for your feedback!

Renamesem5.logtosem5.log.old Path, for 32 Bit: "C:\Program Files\Symantec\Symantec Endpoint Protection Manager\db\" Path, for 64 Bit: "C:\Program Files (x86)\Symantec\Symantec Endpoint Protection Manager\db\" ClickStart, click onRunand Type “CMD” then clickOK In theCommand prompt(as Administrator Symantec Endpoint Protection 12.1: Best Practices for Disaster Recovery with the Symantec Endpoint Protection Manager http://www.symantec.com/docs/TECH160736Applies ToSQL 2005 Database. TECH134782 March 8th, 2016 http://www.symantec.com/docs/TECH134782 Support / Error when logging to Symantec Endpoint Protection Manager: "Failed to connect to server". Force the recreation of sem5.log.

Unable To Connect To The Database Primavera P6

ClickStart, click onRunand Type “Services.MSC” then clickOKand start theSymantecEmbedded DatabaseService Start theSymantec Endpoint Protection ManagerService. https://www.symantec.com/connect/forums/failed-connect-database-server-sepm Please start the data Error Failed to connect to the server. Symantec Endpoint Protection Manager + Failed To Connect To The Server Translated Content This is machine translated content Login to Subscribe Please login to set up your subscription. Don't have a SymAccount?

Unable to start the embedded database service. this contact form For 32 Bit, type: dbsrv11 -f"C:\Program Files\Symantec\Symantec Endpoint Protection Manager\db\sem5.db" For 64 Bit, type: dbsrv11 -f"C:\Program Files (x86)\Symantec\Symantec Endpoint Protection Manager\db\sem5.db" and pressEnter. Don't have a SymAccount? Submit a Threat Submit a suspected infected fileto Symantec.

Translated Content This is machine translated content Login to Subscribe Please login to set up your subscription. Education Services Maximize your product competency and validate technical knowledge to gain the most benefit from your IT investments. On Management configuration wizard-Under Database server authetication-Get Error 11501:Unable to connect to the database.Make sure that you have entered the correct database parameters and that a firewall is not blocking the have a peek here Solution The following steps have been shown to resolve this issue, depending on the version of SymantecEndpoint Protection Manager installed.

Symantec Endpoint Protection 12.1 Terms of use for this information are found in Legal Notices. This can be confirmed by the following steps: Click Start > Run Type Services.msc > Enter Scroll down to the Symantec services and confirm the state of the service: “Symantec Endpoint This will change directories to the folder containingdbsrv11.exe.

Applies ToSymantec Endpoint Protection 11.1.x or 12.1.x Legacy ID 2010070815342348 Terms of use for this information are found in Legal Notices.

If it stays started then go ahead and log into the Symantec Endpoint Protection Manager and everything should now be working properly. No Yes Products Products Home Threat Protection Advanced Threat Protection Endpoint Protection Endpoint Protection Cloud IT Management Suite Email Security.cloud Data Center Security Blue Coat Products Information Protection Data Loss Prevention Fatal error: Could not open/read file: C:\Program Files\Symantec\Symantec Endpoint Protection Manager\data\inbox\log\traffic\4F9B3F56C8C8010801CC5461C422B1F4.tmp.dat Cause This issue is possibly caused by the SEPM unexpectedly shutting down while processing traffic logs, and being unable to Close Login Didn't find the article you were looking for?

Provide feedback on this article Request Assistance Print Article Subscribe to this Article Manage your Subscriptions Search Again Situation Doing a fresh installation. For 32 Bit Type: "dbsrv9 -f "C:\Program Files\Symantec\Symantec Endpoint Protection Manager\db\sem5.db" For 64 Bit Type: "dbsrv9 -f "C:\Program Files (x86)\Symantec\Symantec Endpoint Protection Manager\db\sem5.db" and press Enter Click Start, click on Run Some services stop automatically if they have no work to do, for example, the Performance Logs and Alerts service". Check This Out Cause When the SEPM was installed, the defaults were used and the default port (8443) was already in use.

Create a SymAccount now!' Symantec Endpoint Protection Manager could not connect to the database. Did this article resolve your issue? Run the management server wizard successfully Able to install Sepm 12.1Applies ToWindows server 2008,64bit Terms of use for this information are found in Legal Notices. OR If the Symantec Endpoint Protection Manager service fails to start then run Management Server Configuration Wizard in order to log in to the Symantec Endpoint Protection Manager.

Border